Over 0–100 km/h, Seal 313 2WD wins (6,00 s vs 6,31 s).
Performance comparison
Simulated drag race 0 → 1,000 m in real time. Synchronised speed counters and stopwatch. Physics calibration on 7 manufacturer measurements.
Simulation
Calibration
Physics model calibrated on manufacturer splits. The limited top speed is not the real aerodynamic top speed of the vehicles.
| Seal 313 2WD | P7i | |
|---|---|---|
| 0–100 km/h | 6,00 s−0,31 s | 6,31 s |
| 400 m standing start | 14,21 s−0,36 s | 14,57 s |
| 1,000 m standing start | 26,32 s−0,06 s | 26,38 s |
| Top speed (electronically limited) | 180 km/h | 200 km/h−20 km/h |
| Power-to-weight ratio | 6,35 kg/hpbetter ratio | 7,18 kg/hp |
Standing-start drag race, calibrated on manufacturer splits. The gap shows at each stage.
Simulated performance at each stage. Winner in green.
| Palier | Seal 313 2WD | P7i |
|---|---|---|
| 0–30 km/h | 1,74 s | 1,66 stight gap |
| 0–50 km/h | 2,90 s | 2,77 stight gap |
| 0–80 km/h | 4,66 s | 4,62 stight gap |
| 0–100 km/h | 6,00 s | 6,31 s |
| 0–120 km/h | 7,72 s | 8,47 s |
| 0–160 km/h | 13,20 s | 14,90 s |
| 0–200 km/h | - | 25,20 s |
| 400 m standing start | 14,21 s | 14,57 s |
| 1,000 m standing start | 26,32 s | 26,38 stight gap |
| Top speed | 180 km/h | 200 km/h |
Manufacturer technical specifications. The power-to-weight ratio is the key physical factor in a drag race.
| Characteristic | Value | Detail |
|---|---|---|
| Power | 313 hp | Pending |
| Torque | 360 Nm | |
| Weight | 1 988 kg | manufacturer kerb weight |
| Drivetrain | - | |
| Gearbox | single-speed reduction |
| Characteristic | Value | Detail |
|---|---|---|
| Power | 282 hp | Permanent Magnet Synchronous Motor |
| Torque | 430 Nm | |
| Weight | 2 025 kg | manufacturer kerb weight |
| Drivetrain | Propulsion | |
| Gearbox | Single-speed fixed gear |
Off the line, the Seal 313 2WD hits 100 km/h in 6.00 s versus 6.31 s for the P7i. Despite the faster sprint time, the P7i is 1 m further along the track at this moment: stronger low-speed acceleration offsets a slower run beyond 100 km/h.
At 200 metres, the Seal 313 2WD is doing 135 km/h against 129 km/h for the P7i. The gap is 0.13 s. The challenger starts to claw back ground.
At 400 metres standing start, the Seal 313 2WD crosses the line in 14.21 s versus 14.56 s. The 0.36 s gap represents roughly 16 m of track - two to three car lengths.
Past 400 metres, the gap narrows. The Seal 313 2WD maxes out at 180 km/h while the P7i keeps accelerating towards 200 km/h. At 600 metres, the gap is down to 0.53 s from 0.36 s at 400 metres.
At 1,000 metres, the Seal 313 2WD finishes in 26.31 s versus 26.38 s, with just 0.06 s to spare. The P7i fails to fully close the launch gap.
Both rivals are electronically governed, but not at the same level: the Seal 313 2WD is capped at 180 km/h, the P7i at 200 km/h. This isn’t a physical engine limit - it’s a manufacturer choice, usually for tyre safety or homologation reasons. Neither car reaches its true aerodynamic top speed.
With two electric powertrains, the difference comes down to power-to-weight ratio (6.35 kg/hp vs 7.18 kg/hp) and transmission (Automatic vs Automatic).
In European road use (130 km/h max), both vehicles reach the legal speed limit in under 9.78 seconds. The 0.31 s difference in 0 to 100 km/h is mostly felt in motorway merging and overtaking.
Swap one of the two models to explore an equivalent duel in the same segment.
Over 0–100 km/h, Seal 313 2WD wins (6,00 s vs 6,31 s).
Seal 313 2WD goes from 0 to 100 km/h in 6,00 seconds (calibrated simulation).
Seal 313 2WD: 313 hp, ratio 6,35 kg/hp. P7i: 282 hp, ratio 7,18 kg/hp.
Seal 313 2WD: 180 km/h. P7i: 200 km/h.